The universal Presentation Switcher / Scaler system is a complete AV switching, processing and controlling all-format, all-purpose solution.
To use the HDBaseT video output in remote locations of up to 70m, this receiver needs to be connected to a THB-350 HDBaseT transmitter (sold seperately).
There is only one power supply needed to power both units the other one can be supplied using PoC / PoE.

Power options
This product can draw power from an external 24V power supply sold separately. Do NOT plug the power supply connector into any other connectors this could cause permanent damages to the product and void the warranty.
The transmitting module (LU-THB-350) can then be powerd via PoE / PoC.

Captive screw plug termination
The captive screw plugs for power, audio, RS232 and contact controls are supplied with the unit. Separate the wires about 2.5 cm long strip off the wire insulation precisely by 5mm from the end. Identify the positive and negative leads for power the original Luxi power supply has a white stripe on the positive wire. If not sure, use a multi meter to verify.

Mounting options
Luxi offers the under desk mount LU-UDM-100 or the mediahub™ table tanks (MHUB-), both sold separately the product also fits many other mounting hardware using 5mm long screws supplied with the mounting hardware to screw onto the product.

Control options
When auto switching is turned off, pressing the "Input Sel." button on the front panel of the THB-350 transmitter will toggle through the 3 video inputs. Three sets of external contact closure push buttons and LEDs can select inputs discretely incl. LED indication when a button is pressed, the associated LED would blink once, then stay on. An RS232 host connected to this RHB-350 (or the THB-350 transmitter) can control all functions.

Auto input switching
By default, the auto switching is turned on. When the respective front panel button on the transmitteris pressed, the 3 LEDs next to it will blink 3 times. To turn off auto switching, press and hold the button for about 7 seconds until the LEDs blink twice or use an RS232 command. When auto switching is turned off, use the push-button, contact closure buttons or RS232 to select the desired input. To engage auto switching again, press and hold the button for >7 seconds until the LEDs blink 3 times or use the respective RS232 command.

Audio output connector wiring
Do NOT connect the sleeve (audio cable shield) to the "-" pin of the audio output this could cause permanent damages to the product and void the warranty.

Video signal path
There are 3 video inputs and 2 video outputs available on the transmitter module. The analog RGB video from the VGA input is transmitted to the scalers analog input. The DisplayPort input signal is fi?rst converted to HDMI and can then be switched with the HDMI input signal.
The selected signal goes to the digital input of the scaler. The scaler converts all video to LVDS, feeds that signal to a HDMI encoder and then distribtes it mirrored to 1x HDMI and 1x HDBaseT output.

Audio signal path
There are threee different audio inputs as well as outputs available on the transmitter module. The digital audio signals from the HDMI and / or DisplayPort inputs are selected by the HDMI switcher and then transported to the scaler module. The scaler de-embeds the audio and outputs it to digital S/PDIF and analogue audio. The analogue output is then mixed with the analogue audio input signal and goes to the balanced / unbalanced analog audio outputs and also to an A/D converter. The HDMI encoder can select this mixed audio or the direct digital audio from HDMI /DisplayPort and directly embed it to the HDMI and HBaseT outputs.

RS232 controls
All functions can by controlled using RS232.
Refer to the RS232 Setup Guide as well as the Quick-Start-Guide in the "Downloads" section to find all the codes needed.

Display power controls
This system features a configurable display power control to enable fully automated system operations without any operator or 3rd party control devices. It will send a "display power off" command via the RS232 ports of both RHB-350 and RHB-350 after the last input signal disappears and will send a "display power on" command as soon as the first input signal is detected and will automatically select that input. The switcher uses one RS232 port to connect to both external hosts (optional only required for setup) and display in parallel with the display in "listening" mode only.

General Features:
HDBaseT receiver with HDMI-A output port
Receiver module for Presentation Switcher LU-THB-350 and other devices
Transmitter Supports input signals: VGA + 3,5mm Stereo Audio, HDMI and DisplayPort
Mirrored Output: HDMI and/or HDBaseT for the same picture on two displays
HDBaseT transmits A/V, RS-232 and PoC to an HBaseT receiver (not included) over up to 70 meters
Integrated scaling function (transmitter) for perfectly fitting signal formats and resolutions
3,5mm stereo audio output for a separate audio extraction
RS232 connector for external control featuring unique RS-232 controlled picture zoom (out) adjustments and selectable video resolutions of common 16:9, 16:10, 4:3 or pixel to pixel modes
Confi?gurable display power controls via RS232 enables fully auto operation systems without any 3rd party controller
Slim construction for a space saving installation
Universal interface, compatible with all source signal formats
VGA, HDMI, DP input, auto switch or front panel, RS232, contact controllable with discrete input LED indications
Independent analog audio input - Can be coupled with any video input, mixed with audio, de-embedded from HDMI or DisplayPort outputs to bal/unbal analog output, or embedded to HDMI
Dual mirrored A/V outputs: HDBaseT for big screens / projectors and HDMI for local monitors,
With or without OSD or screensaver and function to enable monitor sleep/wake up (energy saving)
HDBaseT output sending signals in up to 70m incl. PoC
High effi?ciency fanless design for ultimate reliability
Rack mountable, under-table mountable, above-projector mountable metal enclosures